Wisdomlong Technology CO.，LTD
Wisdomlong Technology CO.，LTD
Add to Cart
GE IC693ALG391 Series 90-30 Programmable Logic Controller 2-Channel 12 bits of binary
Product information GE IC693ALG391 :
IC693ALG391 receives negative data, it outputs the low end of the current range of 4 mA to 20 mA range. The software tends to reject any value more than 32767 keyed in the modules. The IC693ALG391 gives two output ranges that are 4 and 20 mA. These two output ranges have user information laid down to make sure that a count of 0 is equal to 4 mA and a count of 32000 is equal to 20 mA. Every 1000 additions equal to 0.5 mA.
In case the CPU is switched to STOP mode or RESET, when measuring Current Output, 4 to 20 mA Output, 0 to 20 mA the condition of the module changes to either Default to 0/4MA or Hold-Last-State. Choosing the suitable condition is created by arranging the DEF0/4 jumper on the detachable terminal board connector on the module.
Every 2-Channel Analog Current Output can be utilized as a current source/less accurate voltage source. A voltage is an output at VOUTx which is equal to the current output. The voltage range relies on the layout of the current output range and may be added with the use of a 250-ohm resistor instead of voltage jumper.
An isolated +24 VDC power supplied by the PLC power supply is the primary power source provider for IC693ALG391. There are two terminals offered to the module's I/O terminal board for user-supplied +24 volts. These terminals are important since they offer a standby power supply to enable the outputs to retain their value when the internal supply is lost and Hold-Last-State is chosen.
When the applied voltage is higher than the isolated +24 VDC that is from 21.5 volts to 26.5 volts, the the user supply is utilized. Further, an inside voltage source of about +24V is produced within the module to run the current loop outputs.
These current loop drivers are source type drivers. To reduce the loading and noise capacitive, all field linked to the module should be wired with the help of a good grade of twisted and protected tool cable connected to GND. This GND link offers access to the baseplate leading to turning down of noise. Three of Analog Current Output modules can be set up when the user given suppliers are not used to power the module.
Series 90*-30 PLCs
GE Intelligent Platforms’ Series 90*-30 PLCs is a family of controllers, I/O systems and specialty modules designed to meet the demand for versatile industrial solutions — helping businesses gain a sustainable advantage. With its single overall control architecture, the Series 90-30 has been the PLC of record in over 200,000 applications such as highspeed packaging, material handling, complex motion control, water treatment, continuous emissions monitoring, mining, food processing, elevator control, injection molding and many more.
Its modular design offers unique versatility.
Configure just the system you need, saving critical space and reducing cost. With over 100 I/O modules, the Series 90-30 PLC can be adapted to a wide range of applications.
• Digital interfaces for push buttons, switches, proximity sensors, relays, contactors and many other devices
• Analog modules with varying degrees of resolution for flow, temperature or pressure applications
• Direct connect wiring or remote termination
| No. of channels: | 2 |
| Ext. Supply Voltage Range: | 20 to 30 VDC |
| Calibration: | Factory calibrated to 4µA per count |
| Update Rate: | 5 msec (both channels) |
| Max Output Load: | 5 mA |
| Power Consumption: | 30 mA from +5 V bus or 215 mA from +24 V backplane or user supply |
Another module:
| IC694MDL230 | 120 VAC Isolated Input (8 Points) |
| IC694MDL231 | 240 VAC Isolated Input (8 Points) |
| IC694MDL240 | 120 VAC Input (16 Points) |
| IC694MDL241 | 24 VAC/VDC Input (16 Points) |
| IC694MDL250 | 120 VAC Isolated Input (16 Points) |
| IC694MDL260 | 120 VAC Input (32 Points)** |
| IC694MDL632 | 125 VDC Input (8 Points) |
| IC694MDL634 | 24 VDC Input, Neg/Pos Logic (8 Points) |
| IC694MDL645 | 24 VDC Input, Neg/Pos Logic (16 Points) |
| IC694MDL646 | 24 VDC Input, Neg/Pos Logic, 1 msec Filter (16 Points) |
| IC694MDL654 | 5/12 VDC (TTL) Input, Neg/Pos Logic, (32 Points) |
| IC694MDL655 | 24 VDC Input, Neg/Pos Logic, 1 ms, (32 Points) |
| IC694MDL660 | 24 VDC Input (32 Points)** |
| IC694ACC300 | Input Simulator Module (8 Points) |
Our brand:
1, First, send us the brand, model code/pic of the nameplate, the quantity for inquiry. Then we will send the quote to you. after confirming the model and the quantity, then we will the PI to you.
2, You can transfer by Paypal/ Western Union/Trade assurance/ T/T. When we received the payment, then we will start to prepare the order for you asap.