Wisdomlong Technology CO.，LTD
Wisdomlong Technology CO.，LTD
Add to Cart
DS3800DMPC GE Mark IV Microprocessor board printed circuit board for use within the Mark IV
Product Description
DS3800DMPC GE Mark IV Microprocessor board
The DS3800DMPC is a printed circuit board manufactured by GE for use within the Mark IV gas and steam turbine management system. The MKIV offered triple modular redundant (TMR) architecture with fault-tolerant control, the first of the Speedtronic systems with this type of two-out-of-three voting on critical controls and protection parameters. MKIV boards like the DS3800DMPC can be found in the AX Control inventory as tested, reconditioned units. We also sell liquidated (never used, like new) surplus stock.
The DS3800DMPC is a microprocessor board. It is a smaller board with only a few components on its surface. The board is drilled at least once in each corner and is marked on its surface with the GE logo and with codes like C-ESS. The top surface of the board is cut away to reveal the bottom layer at each corner.
Board components on the DS3800DMPC include two resistor network arrays, metal film resistors, capacitors made from polyester vinyl material and from ceramic material, jumper switches, and thirteen integrated circuits, including oscillating chips. The board has two connectors. One of these is a right-angled cable connector on the top edge marked 218A4637P5, and the other is a ribbon connector on the bottom edge. This is labeled 278A4702P5A. This connector is typically used to communicate with a DS3800HMPF board when the DS3800DMPC is installed as an auxiliary above that board.
For additional information about installation techniques, handling, or maintenance, please refer to publications from GE like manuals or user guides.
OTHER SUPERIOR PRODUCTS
| Yasakawa Motor, Driver SG- | Mitsubishi Motor HC-,HA- |
| Westinghouse Modules 1C-,5X- | Emerson VE-,KJ- |
| Honeywell TC-,TK- | GE Modules IC - |
| ABB Module | AB Module 1756-,1759- Tourch Screen 2711- |
| Mitsubishi Drive MR- , Motor HA -,HC | Emerson MoudlesVE- ,KJ - |
| Fanuc motor A0-, Drive | Yokogawa transmitter EJA- |
| Rosemount Transmitter 3051- | Schneider Module 140- |
| Panasonic Motor , Drive MH- | Siemens Module 6ES-, Touch Screen 6AV- |
Similar prodcut for GE
DS3800DDCD181A
DS3800DDCD18IA
DS3800DDCD18LA
DS3800DDCD1BIA
DS3800DDCD1BLA
DS3800DDCDI81A
DS3800DDCDI8IA
DS3800DDCDI8LA
DS3800DDCDIB1A
DS3800DDCDIBIA
DS3800DDCDIBLA
DS3800DDCDL81A
DS3800DDCDL8IA
DS3800DDCDL8LA
DS3800DDCDLB1A
DS3800DDCDLBIA
DS3800DDCDLBLA
DS380ODDCD181A
DS380ODDCD18IA
DS380ODDCD18LA
DS380ODDCD1B1A
DS380ODDCD1BIA
DS380ODDCD1BLA
DS380ODDCDIB1A
DS380ODDCDIBIA
DS380ODDCDIBLA
DS3800DDCD1B1A-A
DS3800DDCD1B1A-B
DS3800DDCD1B1A-C
DS3800DDCD1B1A-D
DS3800DDCD1B1A-E
DS3800DDCD1B1A-F
DS3800DDCD1B1A-G
DS3800DDCD1B1A-H
DS3800DDCD1B1A-I
DS3800DDCD1B1A-J
DS3800DDCD1B1A-K
DS3800DDCD1B1A-L
DS3800DDCD1B1A-M
DS3800DDCD1B1A-N
DS3800DDCD1B1A-O
DS3800DDCD1B1A-P
DS3800DDCD1B1A-Q
DS3800DDCD1B1A-R
DS3800DDCD1B1A-S
DS3800DDCD1B1A-T
DS3800DDCD1B1A-U
DS3800DDCD1B1A-V
DS3800DDCD1B1A-W
DS3800DDCD1B1A-X
DS3800DDCD1B1A-Y
DS3800DDCD1B1A-Z
Product Description
The DS3800DBIB is a small printed circuit board (PCB) designed as part of the Speedtronic (Mark IV) line manufactured by GE. The Speedtronic system is designed to sequence turbine fuel and to sequence turbine systems and their auxiliaries for startup. The Mark IV system is designed with a distributed control system which runs on an array of interconnected microprocessors. When one section of this gridwork fails, turbines will continue to work under the control of other parts of the system. In this way downtime is limited. The DS3800DBIB is designed specifically as an interface board.
The DS3800DBIB is a small daughterboard that works as a plug-in to another, larger PCB. It has been drilled out at the factory, one hole in each corner of the board. This board also has four connectors numbered 1 through 4. It has two small screw mounts covered by black tabs. The first mount is marked C101 and is positioned next to a ring marked TP1. The second is not marked and positioned next to a ring marked TP2. The DS3800DBIB has one capacitor rated 708A1, M/E 200V 1.0 +10%. It also has one blue potentiometer located on the edge of the board that is wired for variable resistance. There are ten resistors and six small capacitors marked 'cr' on the DS3800DBIB PCB
Q1. What about the lead time?
A: 3-5 days for Sample preparing ,8-10 working days for mass production.
Q2. Do you have any MOQ limit of Industrial Servo Drives?
A: Low MOQ, 1pc is available.
Q3. How do you ship the goods and how long does it take to arrive?
A: Ship by DHL, UPS, FedEx or TNT. It takes 3-5 days to arrive. Airline and sea shipping also optional.
Secondly, during the guarantee period, we will send new lights with new order for small quantity. For defective batch products, we will repair them and resend them to you or we can discuss the solution including re-call according to real situation.